Page 9: Glossary Of Terms The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade. The distance that the tip of the saw blade tooth is bent or set outward from the face of the blade. Snipe planers Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported. Page Features Maximum nominal lumber sizes The depth guide is used for locking the saw arm in the down position or as a guide for limiting downward movement of the saw arm.
NOTE: Controlling depth of cut is necessary when rough cutting a dado. It retracts over the upper blade guard as the saw is lowered into the workpiece.
To release the saw arm, push down on the top of the saw arm, cut the tie-wrap, and pull out on the depth guide. Page 17 The work clamp provides greater control by clamping the workpiece to the miter table. It also helps to prevent the workpiece from creeping toward the saw blade. This is very helpful when cutting compound miters. Depending on the cutting operation and the size of the workpiece, it may be necessary to use a C-clamp instead of the work clamp to secure the workpiece prior to making the cut.
Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the hex bolt from securing the blade on the spindle.
Page 19 See Figure The laser guide will generate a laser line on the work surface when the saw blade is spinning. The laser line will appear as a broken line on the workpiece when the blade assembly is in the uppermost position and the motor switch is activated.
Page 26 Turn the saw on let blade reach maximum speed , then push the blade down on top of the workpiece then back toward the rear of the saw to make a cut. Cuts are made by: 1 pushing the saw blade away from you and toward the bevel scale at the back of the saw stopping when the full rear position has been reached after each cut. Page 27 Use the work clamp or a C-clamp to secure the workpiece when possible. Page 30 Long workpieces need extra supports.
Supports should be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and miter table during the cutting operation. Use the work clamp or a C-clamp to secure the workpiece. Turn the saw on let blade reach maximum speed , then push the blade down on top of the workpiece then back toward the rear of the saw to make a cut.
Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut. In general, compound miter saws do a better job of cutting crown molding than any other tool made.
In order to fit properly, crown molding must be compound mitered with extreme accuracy. Page 34 23 in. The saw has externally accessible brush assemblies that should be periodically checked for wear.
Brush assembly is spring loaded and will pop out when you remove brush cap. The miter angle should be set crown molding. When cutting warped material, always make sure it is To avoid a kickback and to avoid serious personal positioned on the miter table with the convex side against injury, never position the concave edge of bowed the fence as shown in figure Before performing any adjustment, make sure the tool is unplugged from the power supply.
NOTE: These adjustments were made at the factory and normally do not require readjustment. If the miter lock lever feels loose or the table moves easily when in the locked position, an adjustment to the miter lock lever is required. The saw has externally accessible brush assemblies that When servicing, use only identical replacement should be periodically checked for wear.
Use of any other part can create a hazard or cause product damage. Over time the LED light may become cloudy or dull. If this occurs, the LED lens may require cleaning. Abaisser le levier pour verrouiller la scie en place. Attendre quelques secondes que la lame atteigne sa vitesse de rotation maximale. Lea postura equilibrada. NUNCA utilice la sierra ingleteadora en cuidadosamente el manual del operador.
Aprenda los el piso o estando en cuclillas. Orificio del eje Apriete la palanca hacia abajo para asegurar la sierra en el lugar. Este producto requiere armarse. Si se utiliza un pedestal para sierra ingleteadora, lea el manual del operador y siga las instrucciones del pedestal.
Se suministra un saco captapolvo para utilizarse con la sierra ingleteadora. Nunca utilice una hoja tan gruesa que la arandela exterior de la hoja no se enganche en las partes planas del husillo. Vea la figura Este tipo de corte se usa para elaborar marcos de cuadros, cortar molduras, elaborar cajas con lados inclinados y para ciertos cortes para entramado de techos.
Con el tiempo, es posible que la luz LED se vea opacada o tenue. Si ocurre esto, es posible que la lente LED deba limpiarse.
This manual is also suitable for: Rt. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual.
0コメント