SkyTech P Remote Package. SkyTech TS-3 Thermostat. Current Stock:. Quantity: Decrease Quantity: Increase Quantity:. Facebook Email Print Twitter Pinterest. Warranty Information 1 Year Comprehensive Warranty. Having trouble getting your grill to light up? A common cause of this issue is a defective ignition switch. We'll show you how easy it is to replace the ignitor switch on your Char-Broil infrared g Please note shipping times may be longer than expected due to carrier delays.
Shopping Cart. Submit Search. Sign in Sign in with Password. Cart Shopping Cart 0 item s in your cart. Restore a saved shopping cart. Majestic Fireplace Parts. Preferred Partners of. Continue Shopping Proceed to Checkout. Search within model.
Page A. Add to Cart. Burner with Tiles Nat. Burner with Tiles Prop. Valve Eurosit Nat. Valve Eurosit Prop. Orifice Pilot Nat. Miscellaneous Parts. The appliance, when installed must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C Should this fan require servicing, the power supply must be disconnected. For rewiring of any replacement components refer to Figure 4.
Turn off gas and electricity. Remove burner assembly and rear log support plate. Remove the fan mounting nuts 2 nuts. Slip off the electrical connector at the motor. To reinstall reverse procedure. Thread wire through openings on the right side of fireplace. Do not cut wire or insulation on metal edges. Slide switch assembly from the back, between subframe and trim, then fasten the screw.
For left side installation reverse switch position in bracket and repeat Step 2. Connect wiring to gas valve Fig. Determine height of adjustment. Loosen the four 4 screws. Set bar at proper height and tighten the screws. Add the two 2 extra screws to prevent any movement. Any flue damper must be removed or blocked open. The chimney must be clean and in good working order and constructed of noncombustible materials.
Make sure that all chimney cleanouts fit properly so air cannot leak into the chimney. Install the appliance without trim frame and make all gas fittings and electrical connections. Install the decorative trim frame. Please refer to the Frame Assembly instructions. Installer must attach red warning plate with screws supplied with the gas fireplace insert to the inside of the firebox of the fireplace into which the gas fireplace insert is installed.
Cutting any sheet metal parts of the fireplace, in which the gas fireplace insert is to be installed, is prohibited. If the factory-built fireplace has no gas access hole s provided, an access hole of 1. This access hole must be p lugged with a noncombustible insulation after the gas supply line has been installed.
Some factory-built fireplaces have air passages on face of fireplace for zero clearance capabilities. All trim kits are designed so as to allow airflow to these passages. Under no circumstances should these passages be blocked. The collar extending down from the termination base is the air intake connector. Be sure the flex vent, which is connected to this collar, is also connected to the labelled air intake flue collar on the fireplace.
Make sure the Flex vent is attached on the correct collar and cap for exhaust as well. Slide the insulation provided in the termination kit over the two 2 3" flex liners, to be attached to the 3" Flue collar and cap of the termination.
Feed one 3" flex vent from the bottom of the termination up through the 4" sleeve. Apply hi-temp sealant on the rain cap collar and slide the flex vent over the end of the rain cap collar fastening with the clamp provided. Slide the flex liner back down the 4" sleeve until 4" cap slides over the sleeve. Attach cap to the sleeve with four 4 screws supplied.
Apply hi-temp sealant over the air intake. Feed the two flex liners down the chimney through the damper opening. Tighten termination to the chimney using the screws provided. In case the fireplace opening is only minimum height 21" mm and access from the front is not possible, then follow the instructions below.
Remove flue collar plate assembly. Unbolt the top fastener plate and move it to the back first before sliding the flue collar plate out from the top of the unit. Apply a bead of hi-temp sealant on the end of the collar before attaching the liner to the flue collar. Fasten it with two clamps then adjust fastener plate all the way to the back before sliding flue gas plate back onto the unit.
After the flue collar plate is set on the cabinet top, make sure the front edge of the flue collar plate is completely in contact with the back edge of the cabinet top. Put the machine screw back into the fastener plate. Bolt the plate until it is locked. NOTE: Insulation can be installed above the damper area only, provided the insulation material is of noncombustible type.
Under no circumstances should insulation be put between the damper and the top of the unit. This may cause condensation and overheating of the unit. Remove refractory from package. Refractory are fragile and must be handled with care. Where at all possible, two hands should be used when handling. Take center refractory and tilt so bottom edge slides into support angle in back of fireplace. Now press center refractory to back side of fireplace and hold in place.
Take left or right refractory and align it so leading edge faces outward. Place refractory in fireplace side and slide it forward into side support angle on fireplace front. Leading edge of refractory must be completely behind side support angle of RHEDV32 for proper placement.
Now carefully slide in back side of refractory against fireplace side. Repeat steps 6 and 7 for remaining side refractory. When side refractory is installed correctly, the center refractory will be supported by the side refractory. NOTE: Air intake has a blue line on the vent. Only ceramic glass approved by Vermont Castings, Majestic Products may be used for replacement on this unit. The use of substitute glass will void all product warranties. Care must be taken to avoid breakage of the glass.
Under no circumstances should this appliance be operated without glass properly installed, or with any cracked or broken glass. Replacement of any glass assembly as supplied by the manufacturer should be done by a licensed qualified service person. It will be necessary to clean the glass periodically. During start-up condensation, which is normal, forms on the inside of the glass and causes lint, dust and other airborne particles cling to the glass surface.
Also initial paint curing may deposit a slight film on the glass. It is therefore recommended that the glass be cleaned two or three times with a non-ammonia household cleaner and warm water we recommend gas fireplace glass cleaner. After that the glass should be cleaned two or three times during each heating season depending on the circumstances present.
Remove logs from packaging. Place rear log JR4, KR4 or SR4 on rear bracket ensure log is seated properly, leveled and centered to the unit , so it will not move from side to side and is firmly positioned on the bracket. Use log's bottom holes to locate it into the left bracket log locator studs. Use log's bottom holes to locate it into the right bracket log locator studs. Place burner lava rock material on top of burner.
0コメント